A+ System Board User’s Manual 75300331. • Copyright This publication contains information that is protected by copy- right. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders. This publication is provided for informational purposes only. • Battery: • Danger of explosion if battery incorrectly replaced. • Replace only with the same or equivalent type recommend by the manufacturer. Currently I would recommend the DFI Lanparty for single processors (dual or quad-core) and the Tyan S2696 for dual processors (dual quad-core Xeons for 8-core madness). The Lanparty is around $150 and the Tyan is around $400-$500. Here's other similar drivers that are different versions or releases for different operating systems. It is highly recommended to always use the most recent driver version available. Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. • Dispose of used batteries according to the batter y manufacturer’s instructions. Joystick or MIDI port: • Do not use any joystick or MIDI device that requires more than 10A current at 5V DC. • Notice This user’s manual contains detailed information about the system board. If, in some cases, some information doesn’t match those shown in the multilingual manual, the multilingual manual should always be regarded as the most updated version. The multilingual manual is included in the system board package. To view the user’s manual, insert the CD into a CD-ROM drive. • Table of Contents Chapter 1 - Introduction 1.1 Features and Specifications.. 1.2 Package Checklist..Chapter 2 - Hardware Installation System Board Layout.Installing the CPU..System Memory..Jumper Settings..Rear Panel I/O Ports.. I/O Connectors..Chapter 3 - Award BIOS Setup Utility 3.1 The Basic Input/Output System. Kt400a driver for mac. Digi 002 Rack with Pro Tools LE 6.1 for Windows XP Requirements Digidesign Hardware Supplied with System • Digi 002 Rack • FireWire Cable (12') Digidesign Software Supplied with New Digi 002 Systems • Pro Tools LE 6.1 for Mac OS X & Windows XP • DigiRack Plug-Ins Pro Tools software will not work in 'standalone' mode without the Digidesign hardware installed. ![]() • Introduction Chapter 4 - Supported Softwares 4.1 Desktop Management Interface.4.2 Drivers, Utilities and Software Applications.4.3 Installation Notes..Appendix A - Using the Suspend to RAM Function A.1 Using the Suspend to RAM Function.Appendix B - System Error Messages B.1 POST Beep.. • Introduction Chapter 1 - Introduction 1.1 Features and Specifications 1.1.1 Features Chipset ® • nVIDIA nForce2 chipset nForce2 Ultra 400 nForce2 MCP-T Processor The system board is equipped with Socket-A for PGA processor. Dfi Lanparty Nf4 DriversIt is also equipped with a switching voltage regulator that auto- matically detects 1.100V to 1.850V. • Introduction Expansion Slots • 1 AGP slot • 5 PCI slots AGP (Accelerated Graphics Port) AGP is an interface designed to support high performance 3D graphics cards. It utilizes a dedicated pipeline to access system memory for texturing, z-buffering and alpha blending. The AGP slot supports AGP 8x with up to 2132MB/sec. • Introduction Onboard Dual LAN Features ® • nVIDIA nForce2 MCP-T and ICS1893 Phy Full duplex support at both 10 and 100 Mbps • Realtek RTL8110S Gigabit LAN Full duplex support at 10, 100 and 1000 Mbps • Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compatible •. • Introduction IrDA Interface The system board is equipped with an IrDA connector for wire- less connectivity between your computer and peripheral devices.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |